How a radon mitigation system works: parts, types and what to expect
The short answer
Most systems are soil suction (also called sub-slab depressurization or active soil depressurization). A pipe goes through the floor into the soil or gravel under the house. A fan, kept out of living space, pulls the radon-laden soil gas up the pipe and lets it out above the roof. Because the fan keeps the air under the floor at lower pressure than the house, radon is no longer drawn inside. Sealing cracks helps the system work. A gauge or alarm shows the fan is running, and a retest afterward shows whether it worked. EPA says some systems cut radon by up to 99 percent.
Why radon gets in
Radon comes from the breakdown of uranium in soil, rock and water. The air pressure inside a home is usually lower than the pressure in the soil around the foundation, so the house "acts like a vacuum, drawing radon in through foundation cracks and other openings" (EPA Consumer's Guide). EPA says soil gas is the main source of high radon in U.S. homes. New to radon? Start with what radon is.
A mitigation system flips that pressure difference.
The basic idea: soil suction
EPA says the method used most is "a vent pipe system and fan, which pulls radon from beneath the house and vents it to the outside." It is called a soil suction system, and it "does not require major changes to your home" (EPA Citizen's Guide). You will also see it called sub-slab depressurization or active soil depressurization.
How it works, step by step (EPA Consumer's Guide; Michigan EGLE):
- A suction point. One or more pipes go through the floor slab into the crushed rock or soil underneath. EPA says "often, only a single suction point is needed." EGLE describes contractors drilling a four-inch hole and digging out a pit "about the size of a five-gallon pail," or using an existing sump or drain tile.
- A fan pulls on the pipe. The radon vent fan draws gas from under the home and releases it outdoors, "while simultaneously creating a negative pressure or vacuum beneath the slab." With lower pressure under the floor than in the house, radon is no longer pushed in through openings (EGLE).
- The exhaust goes up and away. The pipe, usually plastic (PVC), lets the gas out above the roof, where EPA says it "is quickly diluted."
- Openings get sealed. Sealing cracks and other openings "makes this kind of system more effective and cost-efficient" (EPA Citizen's Guide).
- A gauge or alarm shows whether the fan is working (more below).
The pipe can run inside the house (for example, through a closet) or up the outside wall. National Radon Program Services notes an outside route "can reduce radon quite well, but it may not be as visually pleasing as one routed through an interior closet" (NRPS).
Types of systems, by foundation
EPA groups the options by foundation type. Many homes have more than one type (for example, a basement under part and a crawlspace under the rest), and then a combination may be needed (EPA Consumer's Guide).
| System | Where it's used | How it works (EPA's description) | Typical reduction (EPA table) |
|---|---|---|---|
| Active sub-slab suction | Basement and slab-on-grade homes | Pipe(s) through the slab, fan pulls from the gravel or soil below. "The most common and usually the most reliable" method | 50–99% |
| Drain-tile suction | Homes with drain tiles or perforated pipe around the foundation | Suction on the existing drain tiles | 50–99% |
| Sump-hole suction | Basements with a sump pump | The sump is capped so it still drains water and also serves as the suction point | 50–99% |
| Block-wall suction | Basements with hollow block walls | Depressurizes the hollow block wall, often together with sub-slab suction | 50–99% |
| Sub-membrane suction | Crawlspaces with an earth floor | A high-density plastic sheet covers the floor; a pipe and fan pull radon from under the sheet. EPA calls it "the most effective way to reduce radon levels in crawlspace homes" | 50–99% |
| Passive sub-slab suction | Usually new homes built radon-resistant | Same pipe, no fan; relies on natural air pressure. Not as effective as active suction | 30–70% |
Source for the table: EPA's "Radon Reduction of Various Mitigation Techniques" table and technique descriptions in the Consumer's Guide. These are typical ranges, not a promise for any one home.
Other methods EPA lists include house or room pressurization, a heat recovery ventilator (HRV) and opening windows (natural ventilation). EPA says pressurization should only be considered after the more common techniques haven't worked, and that natural ventilation is "only a temporary radon reduction approach," since radon levels most often return to previous values within about 12 hours of closing up (EPA Consumer's Guide).
Sealing alone isn't a fix. EPA "does not recommend the use of sealing alone," because by itself it "has not been shown to lower radon levels significantly or consistently," and normal settling of a house opens new entry routes (EPA Consumer's Guide; EPA Home Buyer's Guide).
Radon in well water is a separate problem with separate equipment (aeration or granular activated carbon). EPA says radon entering through water is usually a small risk compared with radon from soil (EPA Consumer's Guide). Ask your state radon office if you're on a private well.
What happens on install day
- Inspection and diagnostics. The contractor inspects the home and may run diagnostic tests. One EPA describes is a "soil communication test," which uses a vacuum cleaner and chemical smoke to see how easily air moves under the floor. That helps decide where the suction point goes and what fan is needed (EPA Consumer's Guide; Minnesota Dept. of Health).
- Combustion appliances. EPA notes a contractor may raise concerns about backdrafting of furnaces or water heaters and recommend having them checked by a qualified inspector.
- Time. Pennsylvania DEP says installation "should take less than a day" (PA DEP). Michigan EGLE says "a day or less."
What a finished system should have
EPA lists basic installation requirements your contractor should meet, and says to confirm the system meets radon mitigation standards and any state rules (EPA Consumer's Guide):
- A label on the system, so nobody changes it by accident. Minnesota's health department says the tag lists the installer's name, phone number, install date and license number (MDH).
- Exhaust above the roof, at least 10 feet above the ground, and at least 10 feet from windows, doors or other openings unless it vents at least 2 feet above them.
- The fan outside living space. It "must not be located in or below a livable area," such as in unconditioned space. Common spots are attics, garages and the outside of the house. An outdoor fan must meet local codes for exterior use.
- Wiring to local electrical code.
- A warning device that tells you if the system stops working: a liquid gauge (manometer), a sound alarm, a light, or a dial gauge, placed where you can see or hear it.
- Written operating and maintenance instructions and copies of any warranties.
Standards: EPA now takes part in the industry-led ANSI/AARST standards process. The current standard for houses is Soil Gas Mitigation Standards for Existing Homes (ANSI/AARST SGM-SF-2023), free to view online (EPA Radon Standards of Practice; AARST). EPA's Home Buyer's Guide says any system must meet your state's rules; where a state has no rules, EPA recommends following its "most current voluntary consensus-based standards" (EPA Home Buyer's Guide).
Testing after installation
- When: EPA says a post-mitigation test should be done within 30 days of installation, but no sooner than 24 hours after the system starts running with the fan on. It recommends a 2- to 7-day test, with windows and doors closed 12 hours before and during the test, except for normal coming and going (EPA Consumer's Guide).
- Who: the contractor may test their own work, but EPA recommends also getting an independent test, by an independent tester or by doing it yourself, to avoid any conflict of interest. You can get a radon test kit or hire a tester (see test kit vs. professional).
- What the number means: see how to read your radon result. EPA says that with today's technology, levels in most homes can be reduced to 2 pCi/L or below.
- Later: EPA says to retest at least every two years. Also retest after major remodeling, like finishing a basement. Pennsylvania DEP suggests testing every two years, generally in the basement and preferably during the heating season (PA DEP).
Living with the system
- Leave the fan on. EPA: the fan "should NEVER be turned off; it must run continuously for the system to work correctly."
- Glance at the gauge. On a U-tube manometer, Pennsylvania DEP says the fan is running if the liquid levels on the two sides are uneven. If they're even, the fan may not be working, so call your installer (PA DEP).
- Fans wear out. EPA says fans may last five years or more and manufacturer warranties tend not to exceed five years (EPA Consumer's Guide). NRPS says typical warranties are 5 years, with life spans of 10–15 years (NRPS).
- Running cost. Fan systems slightly raise the electric bill, and most systems lose some heated or cooled air. NRPS compares the fan's electricity use to a 60–90 watt light bulb running all the time. For dollar figures (and how old they are), see radon mitigation cost.
Who can install one in IN, OH, MI and PA
EPA and CDC both say to use a qualified or certified contractor and to start with your state radon office (EPA; CDC).
- Indiana: under the Indiana radon rule (410 IAC 5.1), anyone doing radon testing or mitigation in homes must be certified by the Indiana Department of Health (IDOH). See the Indiana guide.
- Ohio: the Ohio Department of Health licenses the contractors who install systems and the mitigation specialists who design and supervise them (ODH). See the Ohio guide.
- Michigan: EGLE says Michigan does not license or regulate radon contractors, so it advises using someone certified by one of the two national programs, the National Radon Proficiency Program (NRPP) or the National Radon Safety Board (NRSB) (EGLE). See the Michigan guide.
- Pennsylvania: Pennsylvania DEP tells homeowners to contact a certified radon mitigation contractor and keeps a mitigator list sorted by county (PA DEP). See the Pennsylvania guide.
Before you hire, EPA suggests getting more than one estimate, checking references, and getting a written contract that spells out the work, any guarantee to reduce radon below a set level, warranties, and whether they transfer if you sell (EPA Consumer's Guide). Buying or selling? See radon in real estate deals.
Frequently asked questions
How does a radon mitigation system work?
In most homes it is a soil suction system: a pipe runs from the soil or gravel under the floor slab to the outdoors above the roof, and a fan in the pipe pulls radon from below the home and vents it outside while keeping the space under the slab at lower pressure than the house, so radon is not drawn in through cracks and openings (EPA Consumer's Guide to Radon Reduction).
Does the radon fan have to run all the time?
Yes. EPA's Consumer's Guide says the fan should never be turned off; it must run continuously for the system to work correctly.
How do I know my radon system is working?
Check the warning device, usually a U-tube manometer, regularly. Pennsylvania DEP says the fan is running if the liquid levels on the two sides of the tube are uneven; if they are even, call your installer. Then retest: EPA says to do a post-mitigation test within 30 days of installation, but no sooner than 24 hours after the system starts running, and to retest at least every two years.
Can I just seal the cracks instead?
EPA does not recommend sealing alone. It says sealing by itself has not been shown to lower radon levels significantly or consistently, though sealing is a basic part of most systems.
How long does installation take?
Pennsylvania DEP says installation should take less than a day, and Michigan EGLE says systems can usually be installed in a day or less.
How much can a mitigation system lower radon?
EPA says some radon reduction systems can reduce radon levels by up to 99 percent and that with today's technology radon levels in most homes can be reduced to 2 pCi/L or below. EPA's table lists 50 to 99 percent typical reduction for active soil suction methods.
Sources
- Consumer's Guide to Radon Reduction: How to Fix Your Home (EPA 402/K-10/005), U.S. EPA (PDF marked 2025).
- A Citizen's Guide to Radon (EPA 402/K-12/002), U.S. EPA (PDF marked 2025).
- Home Buyer's and Seller's Guide to Radon (EPA 402/K-24/001, revised March 2024), U.S. EPA (2024).
- Radon Standards of Practice, U.S. EPA (last updated July 9, 2026).
- Soil Gas Mitigation Standards for Existing Homes (ANSI/AARST SGM-SF-2023), AARST (Indoor Environments Association) (2023).
- Find a Radon Test Kit or Measurement and Mitigation Professional, U.S. EPA (last updated November 10, 2026).
- Radon and Your Health, CDC (June 18, 2026).
- Radon in the Home, Pennsylvania DEP.
- Indoor Radon (Radon mitigation systems section), Michigan EGLE.
- Radon Information for Homeowners, Indiana Department of Health.
- Radon Education and Licensing Program, Ohio Department of Health.
- Radon Mitigation Systems, Minnesota Department of Health (last updated 10/03/2024).
- Installing Mitigation, National Radon Program Services, Kansas State University.
Check radon data for your county
See EPA zones and state test results for every county in Indiana, Ohio, Michigan and Pennsylvania. Full county pages with licensed pros: Lancaster County, PA, Allen County, IN, DeKalb County, IN.
This guide is for general information only. It is not medical, legal, or engineering advice. Read our disclaimer.